Concox and Jimi trackers are some of the most common GPS devices in India and many other countries. They're affordable, small and easy to install. Most of them, and many other brands, use the same GT06 protocol, which Traccar supports on port 5023.
This guide connects one to your Traccar server.
Is my device a GT06-protocol tracker?
Traccar's device list shows more than 100 models on the gt06 protocol, including Concox GT06N, GT06D, GT06E, GT07 and GT09, many Jimi models and plenty of unbranded trackers. Search your model on our supported GPS devices list to confirm the protocol and port.
If your model isn't listed, it may still use GT06. The steps below include a way to check.
1. Open port 5023 on your server
GT06 trackers connect over TCP:
sudo ufw allow 5023/tcp
If your server is behind a cloud firewall (security group), open the port there too.
2. Add the device in Traccar
- Find the IMEI: it's on the device label, or reply to the
IMEI#SMS command on many models. - In Traccar, add a device with a name (for example the vehicle number) and the IMEI as the identifier.
3. Configure the tracker by SMS
Send these commands to the SIM card number inside the tracker. Exact commands vary slightly between models and firmware, and some models need a password prefix, so check your device manual if one doesn't work.
Set the mobile data APN (use your SIM operator's APN):
APN,your.apn.here#
Point it at your server by domain name:
SERVER,1,track.yourdomain.com,5023,0#
Or by IP address:
SERVER,0,203.0.113.10,5023,0#
Set the reporting interval, for example every 10 seconds while moving:
TIMER,10,300#
Ask the device for its current settings, to check what it saved:
PARAM#
The tracker usually replies with an SMS confirming each command.
4. Watch the Traccar log
Open the log while the tracker connects:
tail -f /opt/traccar/logs/tracker-server.log | grep gt06
What you might see:
| Log shows | Meaning | Fix |
|---|---|---|
| Lines with gt06 and your device positions | Working | Check the map |
| Unknown device and a number | Data arrives, identifier doesn't match | Copy that number into the device identifier in Traccar |
| Data on a different protocol port | Device isn't GT06 | Use that protocol's port instead |
| Nothing at all | Tracker isn't reaching the server | Check APN, data balance, server address, port and firewall |
GT06 messages start with the bytes 78 78 (or 79 79), which you'll see in hex in the log. That's a quick way to recognise the protocol.
5. Ignition, power and alarms
GT06 trackers report more than position:
- Ignition on and off, if the ignition wire is connected, for trip reports and engine hours
- External power cut alarm, useful against tampering
- SOS alarm on models with a panic button
- Low battery of the internal backup battery
Create Traccar notifications for the ones you care about, for example an Alarm notification for power cut and SOS.
6. Remote engine cut (immobiliser)
Many GT06 models support cutting the fuel or starter relay remotely. Traccar can send the engine stop and engine resume commands to supported devices from the web interface or app.
Use this carefully: only wire it so the engine can't be stopped while the vehicle is moving at speed, follow local rules, and test it with the vehicle parked.
Troubleshooting checklist
- SIM has an active data plan and isn't PIN-locked.
- APN matches the SIM operator.
- Server address and port 5023 are correct.
- Firewall allows TCP 5023.
- Identifier in Traccar matches the number in the log.
- The device has GPS signal (first fix outdoors can take a few minutes).
Summary
Concox, Jimi and other GT06 trackers connect to Traccar on port 5023 with three SMS commands: APN, SERVER and TIMER. The Traccar log tells you exactly which step fails.
Setting up many trackers for customers? My Traccar installation and setup service includes getting your first devices online, and the white-label platform gives you a branded platform and app to sell tracking under your own name.
